Posts Tagged ‘Poulsbo’

« Older Entries

Reasons Your Heat Pump Can’t Maintain the Right Temperature in New Castle

Thursday, March 22nd, 2012

When you set your thermostat in New Castle for a certain temperature, you expect that your heat pump will either heat or cool it to that temperature, right? When you want 72 degrees, you don’t expect to have the temperature stay stuck at 70 degrees while your heat pump struggles futilely.

Sometimes heat pumps have trouble maintaining the right temperature, especially in heating mode. It’s not uncommon, and it has a number of potential causes. Run through this checklist to see if it is something you can fix yourself:

  • The outdoor unit is iced up. Running a defrost cycle can usually fix this.
  • A snow drift in encroaching on the outdoor unit, making the unit too cold to work properly. Shovel it away and see if that fixes the problem.
  • The outdoor unit is not running at all. Sometimes this is simple enough to fix on your own. Read the manufacturer’s instructions to troubleshoot the problem.
  • Too much cold air is getting in the house for the heat pump to keep up. Make sure your doors and windows are closed to keep that valuable heat inside.
  • Your vents are closed. It may seem obviou, but problems like this can sometimes be attributed to user error. Make sure your vents are open to allow heat in.

This is by no means an all-inclusive list, and it covers just those causes that you could potentially fix yourself. There are many other possible culprits out there that could be more sinister and require professional heating system repairs.

Some of these include:

  • The compressor is not running.
  • A compressor valve or reversing valve is faulty.
  • The thermostat is malfunctioning or needs to be recalibrated.
  • The refrigerant level is low or there is a problem with the flow of the refrigerant.
  • The heat pump needs routine maintenance.

If your heat pump is not working properly for several days, especially after you have tried some of the DIY solutions above, call Bob’s Heating & Air Conditioning right away. Your heat pump may need repairs before a bigger problem develops.

Tags: , ,
Posted in Heating, Heating System Repairs, Thermostat | Comments Off

Unusual Heating Tips for Tacoma Residents

Tuesday, February 28th, 2012

Finding new ways to lower the heating bills for your Tacoma home is always a challenge. Maybe you’ve already insulated and sealed every crawlspace and crack, or you might have recently upgraded to that new furnace installation, but there are always other ways to reduce heat loss in the winter.

Here are five ways to conserve heat that you might not have considered.

1. Insulate Recessed Light Fixtures While recessed light fixtures save space and give you more control over lighting and design, such as task lighting in kitchens, they can be a hidden source of heat loss. Feel around your recessed lighting fixtures to see if there’s cool air or a draft. If you do, they could need more insulation. However, you have to be extremely cautious about what type of insulation you use around electrical wiring and fixtures. Check with the manufacturer, or call an electrician if you aren’t sure what type of insulation to use.

2. Insulate Water Heater Tanks Part of your heating bill each month goes to heating the water in your home. Whether you have a gas, electric, solar, or hybrid hot water heater, every water heater tank has an R-value that determines how much heat it loses. If you have a low R-value, your tank may need more insulation. Call a professional plumber or check your owner’s manual for the R-value of the model you own, but the general rule is that if the tank is warm when you touch it, you may need to buy a “jacket” for your water heater. These are fairly inexpensive, easy to install, and can be found relatively anywhere you buy insulation.

3. Open Curtains on South End The southern end of your home will get the most sunlight in the winter. If you have curtains or blinds on your windows or doors, leave them open during the day, and make sure you close them at night. Opening them will help warm up the home naturally during the day, and closing them will help keep the cold air out and warm air in at night.

4. Storm Windows and Doors Many homeowners know they have the option of upgrading old doors and windows that leak air, but not everyone can afford to upgrade all the doors and windows at once. You can also install storm windows and doors to help reserve heat. Before you start comparing prices, remember to measure, since measurements will affect the cost.

5. Close Fireplace Flue Whenever your flue is open, you are losing large amounts of heat. Close the damper if the fireplace or chimney is not being used. You can also consider upgrading to a more air tight damper.

You can always call Bob’s Heating & Air Conditioning whenever you have questions about lowering your heating costs for your Tacoma home.

Tags: , ,
Posted in Furnace Installation, Heating, Heating Maintenance | Comments Off

Question from Camano Island: What Is Refrigerant Pressure and Why Does it Matter?

Wednesday, January 4th, 2012

Refrigerant is often called the “lifeblood” of mechanical cooling devices in your Camano Island home like refrigerators, heat pumps, and air conditioners. You can compare refrigerant to human blood – it flows to all major components using pressure and gravity. The main function of refrigerant is to transfer heat through a closed loop system. Various heating and cooling (HVAC) components require different operating pressures to move refrigerant and process the “refrigeration cycle.”

In a nutshell, the refrigeration cycle involves refrigerant, which changes from a liquid to a vapor and back to a liquid again by the addition of pressure and heat. In a refrigeration system, pressurized refrigerant passed through an expansion valve into an evaporator and pressure is reduced. The evaporator is a tube which passes by the area to be cooled. When the pressure drops, this liquid refrigerant changes into a vapor, which absorbs vaporized heat from the area around the evaporator. After the heat is absorbed by the refrigerant, it flows to a condenser, where it passes over coils, absorbs heat from the hot vapor, and condenses back into a liquid. The liquid is returned to the compressor and the cycle begins again.

Today’s refrigerants – especially those used in residential applications – are broken down into two different types, labeled R-22 and R-410A. R-22 is made up of a chlorofluorocarbon (CFC) chemical, which has been found to be damaging to the Earth’s ozone layer. It has been replaced by R-410A, which is made up of a hydrofluorocarbon (HFC) chemical and will eventually be phased out by the year 2020. One of the biggest differences between the two are their operating temperatures. HFCs operate at much higher refrigerant pressure.

You don’t have to understand the refrigeration cycle to know that today’s high-pressure HFC refrigerants require different test instrumentation and retrofitted or upgraded mechanical equipment. The change in operating pressure is a small price to pay for a cleaner environment everywhere, including Camano Island.

Tags: , , , , , ,
Posted in Air Conditioning, Heat Pumps | Comments Off

A Tip from Poulsbo: Heat Pump Load Calculation

Wednesday, December 7th, 2011

When purchasing a heat pump, the first thing you should do is determine what type of heat pump you want and how big it needs to be to provide ample heating and cooling to your Poulsbo home. If you are unsure what you need, here are some tips to size a heat pump for your home’s particular needs.

The Importance of Sizing

Before buying anything, consider the cost of an oversized heat pump. A lot of homeowners opt for the biggest device on the market, but they do not realize that they are paying more than necessary for their device. An oversized device cycles on and off more often than is necessary and wears down much faster, resulting in an increased electric bill and faster wear on the device. It is not good for your heat pump or your wallet.

How to Size

To correctly size a heat pump, the first step is to perform a load calculation. This is done by measuring the total volume of the rooms being heated (in cubic meters) and then determining the heating factor based on the type of insulation used.

There are different measurements depending on the type and R-rating of your insulation. For example, a single external wall without any additional insulation has a heating factor of 15. The number of external walls, the insulation in those walls and/or the ceiling and the rating of the insulation will determine the total heating factor for the room.

You will then divide the room volume by the heating factor to determine the number of KW (converted to BTUs) needed to heat that particular room.

Professional Sizing

The reason it is so important to call a professional is that certain things, like poorly insulated windows, cracks in the foundation, leaks in the ducts and other issues can have an impact on the overall heating factor measurement. Additionally, the type of heat pump you choose must be effective when connected to an air handler for your entire home. A professional can make these measurements and ensure the right sized device is selected.

If you are unsure about anything related to sizing and selecting a new heat pump for your home, call a professional in. They will perform a full load calculation and present your options for a new heat pump based on those calculations.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Why Fall Maintenance is Important for Your Heating System in Seattle

Wednesday, November 9th, 2011

When it comes to heating equipment maintenance and repairs in your Seattle home, it does not pay to procrastinate. The longer you put off the maintenance, the higher the probability that your heating system will break down or your heating and cooling contractor will be unable to make an emergency repair when you need it. That’s why fall is the best time of the year to have maintenance and repair procedures performed.

Consider this: when do most people call a heating and cooling contractor? The answer: when they need a repair. The call could come in the middle of the night when a furnace stops working or during a family party on a weekend – both times when it is hard to find someone to do the repair work. Has this happened to you?

You can avoid this aggravation and extra expense by scheduling fall maintenance for your heating system. Fall is often the “slow season” for heating and cooling professionals and many schedule their routine service and maintenance appointments during this time. Contractors expect to be busy during the peak winter months and prefer to spread out the workload as evenly as possible.

Most heating and cooling contractors offer service or maintenance agreements, which lock in at least one or two visits a year for furnace or air conditioner inspection. It is rare to find a contractor who will schedule a furnace inspection during the cold winter months. They know that time is usually saved for people with real emergencies. If you don’t have a service agreement with a contractor, you may want to consider signing up for one and avoid the risk of waiting in line for a furnace repair in the dead of winter.

During fall maintenance, your heating equipment will be switched on and inspected. That may sound routine but by running your heating system early, you may be spared the expense of repairing your system when it fails to operate or run smoothly during the cold months. If there is a problem, it is better to fix it ahead of time.

There is no guarantee that a furnace that is tuned up in the fall will last throughout the winter without needing service. But a little preventive maintenance ahead of time will save a lot of heartache – and dollars – when a real emergency comes up.

Tags: , , , , , , ,
Posted in Heating | Comments Off

4 Ways to Improve IAQ and Reduce Air Pollution in Poulsbo

Wednesday, October 12th, 2011

Your Poulsbo home might be a haven for pollutants that can cause irritation to the upper respiratory system of anyone who comes inside. These allergens and pollutants are easy to remove however by taking some simple steps such as the four listed below:

  1. HEPA Filtration – Step one is to use HEPA filtration to remove as much of what is on the floor as possible through vacuuming. HEPA vacuum cleaners can remove years of cleaners, solvents, dander, mineral build ups and other toxins that tend to accumulate in spaces that normal vacuums cannot reach. It may be a bit of an investment, but a high powered vacuum cleaner can have a tremendously positive impact on your lifestyle and reduce pollutants.
  2. Stop Outside Stuff from Coming In – Some of the worst pollutants your home will face are from outside. So, make sure you have doormats at every door and that your family and friends remove their shoes before coming inside. You can have a second mat inside as a friendly reminder that cleaning the shoes is not an option but a strict necessity.
  3. Humidity Helps – Humidity levels between 30% and 50% reduce the presence of dust mites, molds, bacteria and many other indoor pollutants. Air conditioning in the summer is helpful to reduce humidity. Additionally, look for sources of excess humidity like leaky pipes, standing water, or clothes drying.
  4. Cut the Chemicals – There are a number of high quality household cleaners that don’t contain chemicals. Avoid ammonia, bleach and other chemical laden cleaners that can inflame allergies and pollute the water supply. Your home will be just as clean and you won’t feel uncomfortable afterwards.

Proper cleaning and careful selection of compounds and what goes into your air will help you avoid creating new air quality problems in the house. Done right, this process will make everyone in your home feel more comfortable.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

Save Money When Using Appliances and Home Electronics: A Guide From Auburn

Wednesday, September 14th, 2011

As you are looking around your Auburn home for ways to save money on electricity, it is only natural to linger on the big things like your heating and air conditioning systems. However, there is also a lot to be saved in other areas if you know where to look and how to go about cutting back. Both the type of appliances that you buy and the way that you use them will directly impact your total electric bill every month, so it is certainly worth paying attention to what you are doing and what you could do better.

For one thing, it is almost always worth it to go with an Energy Star certified appliance whenever possible. It does not matter if it is a coffee maker or a washing machine. Every little bit helps and so you will be setting yourself up for much lower electric bill over time when you figure total energy usage into all of your purchases.

Using power strips is also a great way to make saving on electricity easy. No matter what you do, many appliances will draw a small amount of power even when they are switched off. So as long as things like your laptop, TV and toaster are plugged in, they are draining energy whether you are using them or not.

Of course, you could just go around and unplug everything you are not using, but that can get pretty tedious. Plugging these types of appliances and home electronics into a power strip makes it easy to just cut their power supply completely when you do not need them. And switching them back on again is just as easy. You do not even have to go crawling around on the floor looking for the plug.

There are certainly many items that you cannot or do not want to unplug or completely cut the power to at any time. For appliances and electronics that fall into that category, simply make sure you turn them off completely when they are not in use. Many home electronics will automatically switch to a standby mode rather than shutting down completely and it is easy to forget they are still on. However, you will save a lot if you make sure to shut them down completely when they are not in use.

Tags: , , , ,
Posted in Energy Savings | Comments Off

How Do EER and SEER Work? A Question From Poulsbo

Wednesday, September 7th, 2011

If you’ve looked for a new air conditioner recently in Poulsbo, you probably noticed each unit comes with an EER or SEER rating. The former is for room air conditioners and the latter for central air conditioning units. In both cases, the number is a measure of how efficiently the system uses electricity. Effectively, if you buy a system with a high rating, you spend less on electricity. Of course, there are tradeoffs. The higher rated machines tend to cost much more, so as a homeowner, you’ll have to evaluate how much you can spend now and how long it will take to save money from that investment.

How EER and SEER Are Measured

These numbers are required by the government to tell you, the consumer, how many BTUs per hour the device can use for every watt of electricity drawn. The more BTUs a system can use, the better for your bill.

Let’s say you want to buy a 10,000 BTU system to cool your living room and dining room. A pretty standard number for a single room unit is 11, meaning the 10,000 BTU system would use about 900 watts per hour to run at full capacity. We figure this out by dividing the BTUs (10,000) by the watts (900).

There is a lot of math to do here, so many people simply look for a higher number within their price range. But, at what point is the upgrade really worth your extra money?

Choosing the Right Energy Efficiency Rating

The easiest way to describe this is to compare two similar devices with different EERs:

Air Conditioner 1 Air Conditioner 2
BTUs 12,000 12,000
EER 9 11
Watts 1333 1091
Price $300 $450

In this particular case, we can spend more for a device that is the same size but uses less electricity. The question then is whether that increased expenditure will pay off in the short term. Let’s assume each device would be operated for 10 hours per day for 30 days in a typical summer month. That’s 300 hours of operation. If the average cost per kWh in you are is $0.09, it will take 4 hours for the first air conditioner to consume 1 extra kilowatt of electricity equal to an additional $0.09. If your air conditioner runs for four months out of the year, we know that it will operate for a total of 1200 hours. That means:

[(1200 hrs x 242 watts) / (1000 watts/kw) ] x $0.09/kWh = $26

So, you save roughly $26 per year from that high efficiency unit. With a $150 price difference, you will break even after 6 years (though probably sooner if the price of electricity goes up).

Tags: , , , , ,
Posted in Air Conditioning | Comments Off

What Features Should I Look for When Buying an Air Conditioner? A Question From Carnation

Monday, September 5th, 2011

There are so many different types and styles of air conditioners on the market these days in Carnation, it can be difficult to figure out what features are worth paying attention to when it comes time to buy one for yourself.

Of course, the most important thing to do is make sure you get an air conditioner that’s appropriately sized for the space you’re trying to cool. But what should you look for beyond that? Here are a few features you might like to have on the unit you purchase:

  • Energy Efficiency – The more energy efficient your air conditioner is, the less your cooling costs will be. It’s as simple as that. So when you’re evaluating devices, remember that it’s worth paying a little bit more up front for a more energy efficient unit. It will save you money in the long run and you’ll be doing your part to help the environment.
  • Dehumidification – Just about every air conditioner controls humidity to a certain extent in addition to cooling. But some do this better than others. There are also air conditioners with separate dehumidification settings for those days that are more humid than hot. Even when you need both cooling and dehumidification, it’s nice to have control of each of these independently.
  • Timer – Being able to program your air conditioner to switch on and off at different times of day is more than just convenient; it will save you money. You don’t want to leave your air conditioner running all day when you’re not home, but it sure is nice to come home to the comfort of an air conditioned space. If your air conditioner has a timer, you can have both. Just set the unit to come on a half hour or so before you get home and you’ll enjoy cool, refreshing indoor comfort right when you get home without paying through the nose to keep your home cool when no one is there.
  • Easy-to-Use Controls – As simple as this one seems, you might be surprised at how inconvenient the controls on some air conditioners can be. So when you’re evaluating your options, make sure you research how easy each unit is to operate. This can definitely save you from plenty of frustration in the long run.

Air conditioners come in many different shapes and sizes. To make sure your decision works best in your home, do your research well in advance. And if you have any questions, consult your local contractor.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

Do I Need Surge Protection for My HVAC? A Question From Roy

Friday, August 26th, 2011

You probably know that to keep your Roy home’s HVAC system in good working order you need to keep up with regular maintenance. This includes things like changing air filters, cleaning out air ducts and clearing debris from both inside and outside the system. Surge protection for your system may not be something you think of immediately, but like those maintenance tasks, it is an important part of keeping your equipment functioning properly over time.

How Surge Protection Works

Surge protection essentially shuts off your system in the event that power levels in the system rise suddenly and unacceptably. When a sudden increase in electricity occurs, any electronic device is at risk. But, unlike your stereo, your HVAC system costs thousands of dollars – no one wants to lose something so valuable to a surge that could have been prevented. That’s why a surge protector is so vital for your system.

The surge protector monitors the levels of electricity coming into your HVAC system. In the event that a surge occurs for any reason (faulty wiring, a lightning strike, etc.), the surge protector will immediately cut off power to the HVAC unit and shut all of the equipment down.

A Sizeable Investment

Your HVAC system was not an impulse buy. This is a collection of equipment that you probably spent a good deal of money on and that you rely on to keep your family comfortable throughout the year. When you look at it that way, it’s easy to see why it’s worth doing anything you can to protect your investment. Installing a surge protector is a relatively minor expense compared to the money and inconvenience it could save you by preventing serious damage to your HVAC equipment.

Proper Restart

Once a surge protector shuts off your HVAC system, you’ll need to restart it properly. The best thing to do is talk to the contractor who installs your system. They can walk you through the restart process step by step to ensure you know exactly what to do. After going through all that trouble installing a surge protector, the last thing you want is to make a mistake when turning it back on.

If you don’t already have a surge protector in place, call an HVAC professional today and learn what your system needs to be fully protected. It’s a small expense and a quick installation, so there’s no reason to put it off any longer.

Tags: , , ,
Posted in Air Conditioning | Comments Off

« Older Entries